|
SAM_1301
time for more welding 32c and sweating like pig lol
Date: 20/01/12
Owner: Mark + FULYSIC
Views: 75
|
SAM_1302
my tiny work area but we all make do with what we have
Date: 20/01/12
Owner: Mark + FULYSIC
Views: 75
|
SAM_1306
let the sparks fly always handy to have fire extinguisher when do this sort woek
Date: 20/01/12
Owner: Mark + FULYSIC
Views: 86
|
|
SAM_1308
cardboard template for second bit
Date: 20/01/12
Owner: Mark + FULYSIC
Views: 172
|
SAM_1309
cut section out
Date: 20/01/12
Owner: Mark + FULYSIC
Views: 98
|
SAM_1310
tacking second bit in working up towards curve and lightly tapping it with hammer to get shape
Date: 20/01/12
Owner: Mark + FULYSIC
Views: 67
|
|
SAM_1312
put final tacks on it gave it slight work with hammer
Date: 20/01/12
Owner: Mark + FULYSIC
Views: 95
|
SAM_1313
after welding still gotta put bit more on yet
Date: 20/01/12
Owner: Mark + FULYSIC
Views: 91
|
SAM_1316
Another section cut out got little carried away with rust converter
Date: 26/01/12
Owner: Mark + FULYSIC
Views: 45
|
|
SAM_1317
Made carboard template for this one to but put screw in middle so i could hold it as kept slipping inside chassis rail
Date: 26/01/12
Owner: Mark + FULYSIC
Views: 43
|
SAM_1319
this bits all welded needs clean up and should be good
Date: 26/01/12
Owner: Mark + FULYSIC
Views: 41
|
SAM_1322
wire brushed and painted the extractors today but think it might have been little to hot today because paint didn't come out as dark as i thought it would as its meant to be flat black
Date: 26/01/12
Owner: Mark + FULYSIC
Views: 53
|
|
SAM_1324
my rebuild kit for my SU's fresh from the UK
Date: 26/01/12
Owner: Mark + FULYSIC
Views: 42
|
SAM_1329
Cut bigger section out spent fair bit of time cleaning inside as you can see not to bad on inside
Date: 27/01/12
Owner: Mark + FULYSIC
Views: 41
|
SAM_1330
once rust converter dried looks ok in there time to make replacement section
Date: 27/01/12
Owner: Mark + FULYSIC
Views: 38
|
|
SAM_1332
Section made from cardboard template this section was hard due to so many curves etc but ened up with ok fit
Date: 27/01/12
Owner: Mark + FULYSIC
Views: 71
|
SAM_1337
added some weld seems ok and hasn't moved
Date: 27/01/12
Owner: Mark + FULYSIC
Views: 43
|
SAM_1339
all done and welded as you can see i like my rust converter probably little to heavy with it
Date: 27/01/12
Owner: Mark + FULYSIC
Views: 51
|
|
SAM_1344
Made up bit of alloy sheet to cover the big hole left from removing fuel tank plastic is still on the alloy until final fitment
Date: 29/01/12
Owner: Mark + FULYSIC
Views: 40
|
SAM_1345
another picture with flash turned off
Date: 29/01/12
Owner: Mark + FULYSIC
Views: 36
|
SAM_1348
Made up another sheet to level the floor not sure if i like it to much also playing around with fuel pump and filter position
Date: 29/01/12
Owner: Mark + FULYSIC
Views: 58
|
|
SAM_1360
master cylinder and booster
Date: 19/02/12
Owner: Mark + FULYSIC
Views: 64
|
SAM_1359
back of disc rotor
Date: 19/02/12
Owner: Mark + FULYSIC
Views: 76
|
SAM_1358
front of disc setup
Date: 19/02/12
Owner: Mark + FULYSIC
Views: 77
|
|
SAM_1403
The work station
Date: 05/04/12
Owner: Mark + FULYSIC
Views: 65
|
SAM_1448
One side of disc brake front completely rebuilt ready to go back together
Date: 26/04/12
Owner: Mark + FULYSIC
Views: 46
|
SAM_1449
New disc rotor ready for all new bolts bearings and wheel studs
Date: 26/04/12
Owner: Mark + FULYSIC
Views: 70
|
|
SAM_1450
Rebuilt brake caliper
Date: 26/04/12
Owner: Mark + FULYSIC
Views: 27
|
SAM_1451
Another view im going to hand paint the writing with red brake paint
Date: 26/04/12
Owner: Mark + FULYSIC
Views: 37
|
SAM_1452
Dust cover and stub axle all new bearings and new bearing bolt and grease cap
Date: 26/04/12
Owner: Mark + FULYSIC
Views: 38
|
|
SAM_1453
Steering arm grease cap spacer plate
Date: 26/04/12
Owner: Mark + FULYSIC
Views: 25
|
SAM_1456
one side complete
Date: 27/04/12
Owner: Mark + FULYSIC
Views: 63
|
|
