|
Seeing as I was rebuilding the whole front end, I guess I better do the calipers.
Date: 18/11/06
Owner: Shane Hamilton
Views: 43
|
Taking the pins out to remove the pads.
Date: 18/11/06
Owner: Shane Hamilton
Views: 35
|
4 bolts out to split the calipers. The 350Hg's have spacers between the two halves.
Date: 18/11/06
Owner: Shane Hamilton
Views: 44
|
|
Piston seal & clip off.
Date: 18/11/06
Owner: Shane Hamilton
Views: 33
|
Removing the piston, wave the compressed air past the hole so it pulse the piston, it'll work its way out.
Date: 18/11/06
Owner: Shane Hamilton
Views: 46
|
Mmmmm, yummo.
Date: 18/11/06
Owner: Shane Hamilton
Views: 49
|
|
Its been a long time since these calipoers have seen the light of day.
Date: 18/11/06
Owner: Shane Hamilton
Views: 38
|
They look shocking but the cleaned up good, no pitting on the skirts.
Date: 18/11/06
Owner: Shane Hamilton
Views: 28
|
Same again.
Date: 18/11/06
Owner: Shane Hamilton
Views: 35
|
|
A closeup, looks worse than it is.
Date: 18/11/06
Owner: Shane Hamilton
Views: 40
|
Img_1739
Date: 18/11/06
Owner: Shane Hamilton
Views: 37
|
Starting to clean them up.
Date: 18/11/06
Owner: Shane Hamilton
Views: 36
|
|
The old piston seal in the bore.
Date: 18/11/06
Owner: Shane Hamilton
Views: 30
|
Img_1749
Date: 18/11/06
Owner: Shane Hamilton
Views: 32
|
All the crap is gone, new seal is in.
Date: 18/11/06
Owner: Shane Hamilton
Views: 29
|
|
Smeared the piston with brake fluid so it slides in the bore easily.
Date: 18/11/06
Owner: Shane Hamilton
Views: 34
|
New dust seal and clip is on.
Date: 18/11/06
Owner: Shane Hamilton
Views: 35
|
The sealing rings for the spacers.
Date: 18/11/06
Owner: Shane Hamilton
Views: 27
|
|
The spacer with its new sealing ring. This is one of the two 1/8" spacers between the two caliper halves
Date: 18/11/06
Owner: Shane Hamilton
Views: 45
|
Bolted back together.
Date: 18/11/06
Owner: Shane Hamilton
Views: 34
|
Buffed them up a bit before putting them back together.
Date: 18/11/06
Owner: Shane Hamilton
Views: 42
|
|
A bit of reconditioning paint and your all done.
Date: 18/11/06
Owner: Shane Hamilton
Views: 40
|
The new rotors, DBA slotteds.
Date: 18/11/06
Owner: Shane Hamilton
Views: 40
|
This is the other spacer (1/16") needed on the 350 models, if its not on there the caliper will rub on the disc.
Date: 23/11/06
Owner: Shane Hamilton
Views: 60
|
|
This is the hub without the bearing shell.
Date: 30/11/06
Owner: Shane Hamilton
Views: 29
|
So is this but the other side.
Date: 30/11/06
Owner: Shane Hamilton
Views: 33
|
With the new bearing shell "pressed" in.
Date: 30/11/06
Owner: Shane Hamilton
Views: 34
|
|
Same again but the other side.
Date: 30/11/06
Owner: Shane Hamilton
Views: 29
|
Ready to hang off the crossmember.
Date: 30/11/06
Owner: Shane Hamilton
Views: 40
|
|
