|
IMGP9943insert
Date: 06/03/10
Views: 7
New
|
IMGP9935sml
Drip moulds polished and refitted
Date: 05/03/10
Views: 12
New
|
IMGP9933sml
Front and rear screen moulds polished up and ready to be refitted.
Date: 05/03/10
Views: 11
New
|
|
IMGP9919sml
Premier rear door has mounting bosses for the armrest. Others do not
|
IMGP9921sml
Subwoofer box retaining mounts
|
IMGP9924sml
Subwoofer box retaining mounts
|
|
IMGP9906sml
Original EH interior lamp refitted
|
IMGP9908sml
Original EH interior lamp refitted
|
IMGP9912sml
Rear seat belts refitted
|
|
IMGP9905sml
Rear seat belts refitted
|
IMGP9878sml
Hoodlining being installed. It is a tan coloured suede that matches the leather I've chosen for the main trim colour.
|
IMGP9880sml
Hoodlining being installed. It is a tan coloured suede that matches the leather I've chosen for the main trim colour.
|
|
IMGP9885sml
Hoodlining being installed. It is a tan coloured suede that matches the leather I've chosen for the main trim colour.
|
IMGP9882sml
Hoodlining being installed. It is a tan coloured suede that matches the leather I've chosen for the main trim colour.
|
IMGP9888sml
Hoodlining being installed. It is a tan coloured suede that matches the leather I've chosen for the main trim colour.
|
|
IMGP9874sml
Passenger side kick panel and underdash panel awaiting trim
|
IMGP9863sml
Passenger side kick panel and underdash panel awaiting trim
|
IMGP9867sml
Drivers side kick panel and underdash panel awaiting trim
|
|
IMGP9872sml
Drivers side kick panel and underdash panel awaiting trim
|
IMGP9846sml
Final trial fit of centre console. Everything went together well so it's off to the trimmers
|
IMGP9850sml
VR-VS Calais headlight switch fitted to the centre console. Lokar shifter boot and gear display refitted. All OK
|
|
IMGP9857sml
VR-VS Calais headlight switch fitted to the centre console. Lokar shifter boot and gear display refitted. The power/economy switch is just to the right of the shifter and will be painted to match the console..
|
IMGP9813sml
Modified HQ handbrake lever cover finished. I had to section it and extend the lower rear to match the line of the floor.
|
IMGP9818sml
Modified HQ handbrake lever cover finished. I had to section it and extend the lower rear to match the line of the floor.
|
|
IMGP9829sml
Passenger side underdash panel awaiting trim. There will be a small billet lamp in the panel that will match the A/C vent in the console.
|
IMGP9831sml
Inside passenger foot well. all finished. There is 2 heater hoses, 2 A/C hoses, a A/C drain tube, 2 battery cables, plenum drain tube, heater tap cable, ignition module harness and an audio crossover for the passenger front door speaker.
|
IMGP9825sml
Drivers side underdash panel awaiting trim.
|
|
IMGP9840sml
Modified kick panels have had the mounting clips glued into it. These will then be covered by the trim and the clips will be invisible once fitted
|
IMGP9808sml
The aftermarket kick panels are made from extremely flimsy fibreglass that is flat. If I leave them like this and have them trimmed they will be full of wrinkles once they're installed. So I installed them and added 2 layers of fibreglass. This makes them
|
IMGP9809sml
The aftermarket kick panels are made from extremely flimsy fibreglass that is flat. If I leave them like this and have them trimmed they will be full of wrinkles once they're installed. So I installed them and added 2 layers of fibreglass. This makes them
|
